Soldering Tool

Product Details:

This solder wick is a kind of maintenance tool for exclusive use. Our product serves to completely absorb and remove the excess solder. It features high thermal conductivity, as well as strong resistance to both oxidation and corrosion. Moreover, this product can not only enormously reduce the time for reworking or repairing the electronic products, but also minimize the risk of thermal damage to circuit boards.

Its precise geometric design in weaving guarantees the maximum surface tension and tin-absorbing capacity. The solder wick has optimized the heat transport between the woven belt and the solder joint, thereby accelerating the tin-absorbing speed. Owing to the very little flux residue, our product is able to speed up the PCB cleaning process, or even entirely cancel the cleaning process.

Our solder wick has been sold to Canada, Colombia, and Romania, among other countries. We are also looking for new agents on a global scale. You can contact us by email, phone, fax or other methods, so that we can understand your needs.

Product Specifications:

Since its inception in 2006, Jufeng Solder Co., Ltd. has been engaged in the soldering industry for over a decade. We focus on the research, production and sales of such products as the solder wire, solder paste, solder bar, flux, and soldering machines, among others. Our product has passed plenty of international standard certifications, including SGS, RoHS, REACH and more. We can produce the custom-made product. Also, we can offer the OEM processing service as well as the logo design. Welcome to consult us and place an order.

Product Details:

The desoldering wick is a maintenance tool that serves to completely absorb and remove any excess solder. The wick is applied when soldering circuit board chips, aluminum electrolytic capacitors, and other applications to remove tin. The desoldering wick no only enormously reduces the time for reworking or repairing electronic products, but it also minimizes the risk of thermal damage to circuit boards. It features optimized heat transport between the woven belt and the solder joint, thereby accelerating the tin-absorbing speed. Because of its very little flux residue, it speeds up the PCB cleaning process.

Usage:

• Place the desoldering wick over the solder you wish to be removed. Then push the heated soldering iron tip onto the desoldering wick, the solder will be absorbed.
• Remove the desoldering wick after the solder has been absorbed.
• Cut off the used section of the wick.
• Repeat the steps above if the solder is not removed completely. Absorbability may differ depending on the type of solder.

Specification:

Product Details:

The soldering iron kit includes soldering iron, desoldering pump, solder wire, soldering tips, iron safety stand, tweezers, wire stripper, electronic wire, PU tool bag, soldering iron tip cleaner, hot knife, insulation tape.

With ease of use, this soldering iron kit is widely used for welding circuit boards, appliance repair, jewelry welding, etc.


Features:

• High performance ceramic heater: The soldering iron is designed with an 80W ceramic heater, ensuring the desired working temperature can be achieved within 30 seconds. Rapid heat-up and constant temperature provide high quality soldering on various objects.
• Easy operation: It’s easier to carry comparing to the soldering station. This soldering iron comes with a LCD display, clearly displaying the working temperature. The temperature can be easily adjusted between 200°C – 450°C through turning the knob on the soldering iron.
• Good heat dissipation, low power consumption: Four ventilation holes on the soldering iron ensure good heat dissipation. This soldering iron features low power consumption.

Applications:

• Suitable for soldering LED circuit boards, computer and mobile phone motherboards.
• Widely used for welding PCBs (printed circuit boards), and precision circuit boards.
• Suits for lead free soldering electronic components;
• Ideal for DIY hobbyists.

Product Details:

Standard Configuration of Cordless Screwdriver:

• 1 bit holder
• 1 battery charger
• 6 pcs 50mm screwdriver bits

Features:

• The bit holder for the reversible screwdriver shall be charged with DC power.
• Novel and exquisite, the small volume electric screwdriver is convenient to carry.
• Mainly applied for driving in and extracting screws, our rechargeable cordless electric screwdriver makes the maintenance task easier by virtue of the comfortable grip.
• The extra 2 bits make it available for the application on soft material.
• To brighten the dark area, there is LED light designed for the product, resulting in the convenient operation in darkness.
• The LED battery indicator reminds users to charge battery timely.
• For wide applicability, powder metallurgy is adopted for the inner structure of the bit holder. The optimal abrasion resistance and big torsion make for long service life and high efficiency of the cordless screwdriver with LED.

Product Details:

Features:

• The built-in two-chip system for soldering equipment accurately controls the temperature.
• Using fine copper transformer, the rework station features less heat emission, sufficient power, and rapid heat-up.
• The ceramic heating element imported from Japan with original packaging makes for quick heating and temperature recovery, as well as long service life of the anti-static soldering station.
• The external potentiometer contributes to convenient and accurate temperature calibration.
• The universal consumable tip, which is made of common 900M series soldering iron, effectively reduces the production cost.
• Lightweight handle makes the soldering station suitable for long time use.
• To ensure the safety of the sensitive elements and the worker, this product is provided in anti-static design.

Details:

• The red LED power indicator will light on during heat-up.
• Electrodeless temperature adjustment from 200°C to 450°C makes it applicable for different welding processes.
• The power switch is installed sideways.
• The built-in trimming resistor can calibrate the actual temperature difference of the solder tip.
• Equipped with special 5-pin plug, as well as the locking device, the soldering iron is free from disconnection or bad contact. Additionally, machine with 5-pin aviation plug is also available from us, as shown in the picture. The life time can be 5 times that of the regular plug.

Product Details:

Features:

• High cost performance: simple and exquisite, the professional design of the soldering iron is conducive to the outstanding performance.
• Safe engineering: the power line made of pure copper wire in big diameter can provide sufficient power, and has outstanding bending endurance.
• Optimal heating element: the heating element for the soldering tool is made of high-quality thermal fuse. The double wire wrapping effectively prevents the soldering iron from short circuit. Therefore, the service life is prolonged, accordingly.
• Comfortable grip: conforming to human engineering, the heat-resisting resin molding fits closely with hand geometry.

Soldering Station Selection Method:

• 20W and 40W-applicable for welding small element on PCB
• 40W and 60W-specially offered for low voltage switch and transformer
• 60W and 80W-available for soldering wire rod, element with radiator, as well as the solder joint requiring big heat consumption.

Precautions:

• For first time use, there is small amount of smoke produced. Please feel at ease with it.
• The welding tool shall be positioned at the high-quality iron stand to avoid scalding and fire disaster caused by high temperature.
• Do not solder component with iron core pulled out. Otherwise, the service life of the iron core will be shortened.
• Natural cooling is highly recommended. Quick cooling with water will result in short service life of the soldering iron.
• In case there is integrated circuit or COMS element, soldering station with 3-core power line shall be selected to avoid damage to the device caused by induced voltage or drain voltage.
• Utilization of special long-life solder tip is not suggested.

Usage:

• Carefully examine whether the tin at the top of the solder tip is penetrated or seriously oxidized. The solder tip shall be immediately replaced in case penetration is found. For oxidation, brush and sand paper with over 800# grit shall be used for grinding. It is prohibited to conduct grinding with the sand paper or grinding wheel with the grit no more than 800; otherwise, the service life of the solder tip will be seriously affected.
• Stain on the PCB rework equipment is generally caused by the splatter of the scaling powder. Ethyl alcohol shall be employed for cleaning.
• Before using, preheat the soldering iron until the temperature for welding is obtained. Afterwards, slightly wipe the solder tip with watersoaked sponge to remove the oxide layer.
• Immediately, cover the solder tip with newly melted solder tin.
• Preheating shall be conducted on the soldering part with the solder tip.
• After short time preheating, insert the solder tin into the solder tip to have it melted until it flows to the welding position naturally.
• Remove the soldering iron immediately when the solder tin is well integrated with the welded device to avoid excessive welding. Additionally, premature removal of the solder tip will lead to cold welding.
• Under the circumstance welding is completed, clean and cover the solder tip with tin before poweroff.

Maintenance and Storage:

• Before replacing iron core, check if there is solder tip on the core. The old solder tip shall be removed before the replacement of the iron core.
• The acidized substance inside stainless steel tube shall be eliminated first before replacing the iron core.
• To avoid solder tip oxidation and insulativity reduction of the iron core, the soldering iron shall be kept in the circumstance free from high temperature and humidity.

Product Details:

SMT red glue is a kind of polyene organic compound. Compared to solder paste, the red glue will cure after it is heated. Its curing point is 150 after this, it immediately changes from paste to solid. Its outstanding curing speed, high heat-resistivity, and excellent electric properties make this a vital component in soldering. It is ideal for processing SMT series during wave soldering processes.


Specifications before curing:

Recommended curing condition:

• The recommended curing condition is 90 120 sec after surface temperature has reached 150 or 160 180 sec after surface temperature has reached 120 The highest curing temperature should not exceed 200  The ideal curing condition depends on the curing furnace. With a higher curing temperature and longer curing time, the stronger the adhesive strength. The typical curing curve of red glue is as follows:

Specifications after curing:

Curing conditions:

• Absent the presence of special instructions, the curing condition will be 150  for 30 min. The actual adhesive strength of red glue largely depends on the type of component, shape of the glue point, and the curing degree of the glue.

How to use SMT red glue:

• With the one-off syringe packing type, it can be used on normal dot dispensers.
• The red glue should be preserved in a refrigerator maintain quality. Before processing, it should be taken out from the refrigerator and placed down vertically for de-freezing in room temperature (ideal temperature for 20 25 about 2 4 hours until it reaching the room temperature. Hot water, oven, hot plate, heat gun and other heat sources should not be used to speed up de-freezing. This step is extremely important for obtaining optimal dot dispensing performance.

Product Details:

The electric soldering iron is a vital tool for the production and maintenance of electrical components and wires. The soldering iron is ideal for BGA soldering and can be applied for heat-shrinkable sleeve processing, thermal testing, and other common heating processes.

According to different usage requirements, Jufeng Solder provides internal-heat-type and external-heat-type soldering irons.

The internal-heat-type soldering iron is small in volume and affordable. We offer tools with a working power of 20W, 25W, 35W, 50W, etc., among them 35 W and 50 W are most commonly used. The soldering iron has high heating efficiency. And it is easy to replace its soldering iron holder.

The external-heat-type soldering iron is designed for long-life performance and high power, such as 25W, 30W, 40W, 50W, 60W, 75W, 100W, 150W, 300W, etc.

Features:

• Conforming to ergonomic design, the heat-resisting resin molding fits closely with the geometry of your hand. The lightweight insulated handle ensures comfort over long periods of use.
• The ceramic heating element allows quick heating and long service life.
• The specially designed soldering temperature control system can display working temperature precisely and stabilize the temperature with accuracy.
• The soldering station and the welding frame are designed separately. Both are small in volume and easy to place, which takes up minimal working space.
• ESD-safe, meaning it offers better protection of components, with good safety and reliability.

Parameters:

Product Details:

This solder wire drawing machine basically consists of five parts, including the automatic-metering type wire straightening machine, coiling device, motor, electronic control system, and the rack. It is fit for winding the solder wire with its diameter of over 0.1mm. Beyond that, our machine gives the functions of automatic metering and automatic braking. It can be categorized into the large-sized type, medium-sized type, and the small-sized type.

• The drive shaft seat of our solder wire drawing machine is wholly welded, and the hole is drilled for only once. The coaxiality is guaranteed to be ±0.015mm, which allows the spool to rotate smoothly. Additionally, our product can reduce the shaking of solder wire, and also improve the quality of tin wire.
• Our factory adopts an extra drum driven by a motor, which allows the solder wires to be neatly arranged at both ends of the spool.
• This product is designed by taking advantage of the drum type drawing machine from Taiwan for reference. In contrast, it features more simple structure and more preferential price.

Characteristics of Large-sized Solder Wire Drawing Machine: Configurations:

• Motor: 11kW colloidal pin wheel speed reducer with its speed ratio of 1 to 23
• Cooling system
• Automatic wire protection system
• The casing is wholly welded with thick steel plates. The bore-hole does not deform, after the annealing process is completed. This machine features high precision and fast speed. Additionally, the wire is not broken easily.
• The diameter of the leaded solder wire ranges from 4mm to 9mm.

Features of Medium-Sized Solder Wire Drawing Machine:

• This machine remarkably features variable frequency, low noise, high speed, and convenient threading. It can prevent the wire-drawing fluid from spattering.
• The power of the Class 6 motor is 7.5kW.
• This device comes with the spray and cooling system.
• It is also equipped with the automatic wire protector.
• The rack is welded with the thick plate that conforms to the national standard. The bore-hole does not deform, after the annealing process is accomplished.

Characteristics of Small-Sized Solder Wire Drawing Machine:

• Dual Frequency Conversion: The winding speed is adjustable, and the size of the coil can be changed.
• The power of the Class 6 motor is 4kW.